Views 17
Quick Answer
To hem pants: try them on with your shoes and mark the new length. Take them off, add a 1½″ hem allowance, and cut. Fold the raw edge up ½″, then fold up another 1″ and press. Pin it and sew close to the inner fold with a straight stitch or a blind hem stitch. Press again to finish.
Time: 30–45 minutes · Skill level: Beginner · Cost: Under $5 in supplies
What You Need
- Sewing machine (or a hand-sewing needle)
- Thread that matches the pants
- Fabric scissors
- Pins or sewing clips
- Measuring tape and a ruler or hem gauge
- Chalk or a washable fabric marker
- Iron and ironing board
- Seam ripper, if you are removing an old hem
- For jeans: a denim needle (size 100/16) and topstitching or heavy-duty thread
How to Hem Pants on a Sewing Machine: Step by Step
Step 1: Try the pants on with the shoes you’ll wear
Shoe height changes the right length. Stand straight in front of a mirror and fold the pant leg under until it sits where you like. For most trousers, the back hem should just touch the top of the shoe heel. Pin the fold in place at the front.
Step 2: Mark the new length
Take the pants off. Lay them flat and draw a chalk line along the fold you pinned. This is your finished length line. Measure from the crotch seam down the inseam to the line, so you can mark the second leg at exactly the same length.
Step 3: Remove the old hem (if needed)
If the pants already have a hem and you need more length to work with, unpick it with a seam ripper and press the fabric flat.
Step 4: Add the hem allowance and cut
Measure 1½″ below your finished length line and draw a second line. Cut along this lower line. (Use 2″ for dress pants if you want a deeper, heavier hem.) Cut one leg, then use it as a guide to cut the second leg the same length.
Step 5: Finish the raw edge
Fold the raw edge up ½″ toward the inside of the leg and press it with the iron. On thick fabric, you can zigzag or serge the edge instead of folding, which keeps the hem less bulky.
Step 6: Fold up again and press
Fold the hem up again along your finished length line (about 1″) so the raw edge is hidden inside. Press firmly. A crisp press makes the sewing much easier and the hem look professional.
Step 7: Pin or clip the hem
Pin every 2–3 inches all the way around the leg. Check that the inseam and outer seam line up with their own seams above the fold.
Step 8: Sew the hem
Use the free arm of your machine, sliding the pant leg over it. Choose one stitch:
- Straight stitch (length about 3 mm): sew about ⅛″ from the inner fold. This is the easiest, and it shows on the outside, which suits jeans and casual pants.
- Blind hem stitch with a blind hem foot: this gives an almost invisible hem for dress pants. Check your machine manual for how to fold the fabric for this stitch.
Start at the inseam, backstitch a few stitches, sew all the way around, and backstitch again where you started.
Step 9: Press the finished hem
Remove the pins and press the hem from both sides. Try the pants on to check the length, then repeat on the second leg.
Tip: Always test your stitch on a scrap of the cut-off fabric first. It’s the easiest way to check tension and stitch length before you sew the real hem.
How to Hem Pants by Hand (Blind Stitch)
No sewing machine? A hand blind stitch gives a neat, nearly invisible hem, and it’s how many tailors finish dress pants.
- Follow steps 1–7 above to measure, cut, fold, press, and pin.
- Thread a needle with a single strand of matching thread and knot the end.
- Hide the knot inside the hem fold.
- Pick up just one or two threads of the pant fabric right above the fold.
- Slide the needle about ¼–½″ along inside the folded edge of the hem, then come out.
- Repeat all the way around, keeping the stitches loose so they don’t pucker the fabric.
- Tie off with a small knot inside the hem and press.
Which Hemming Method Should You Use?
| Method | Best for | Visible on outside? | Durability |
|---|
| Machine straight stitch | Jeans, casual pants, kids’ pants | Yes | Very durable |
| Machine blind hem | Dress pants, trousers | Almost invisible | Durable |
| Hand blind stitch | Dress pants, delicate fabrics | Almost invisible | Good |
| Iron-on hem tape | Quick or temporary fixes | No | Can loosen in the wash |
How to Hem Jeans and Keep the Original Hem
Want shorter jeans that still have their factory-worn hem? Use the “original hem” method:
- Measure how much shorter you want the jeans, then divide by two. That’s the size of the fold.
- Fold the leg up on the outside by that amount, so the original hem points toward the knee, and pin.
- Sew around the leg just below the original hem’s edge, using a denim needle and matching thread.
- Trim the extra fabric inside to about ½″, and zigzag the raw edge.
- Fold the original hem back down and press. Topstitch close to the seam to hold it flat.
Baggy pants that are too long, pool at the ankles, or cover your shoes may render a great garment look untidy and ill-fitted. Hemming pants will allow you to trim the legs to the right length, make the pants fit better, and add to their comfort.
It is unnecessary to own a sewing machine or have a professional sewing skill set in order to hem pants. Depending on the type of material used for your pants and the desired longevity of the hemming, you can choose to hem the pants by machine, by hand, or using an appropriate hemming product.
The technique depends on such factors as the material of your pants, type of the construction, previous hem, and intended use.
Tough jeans and workwear pants are better to hem in a durable manner, while dress pants look better hemmed in a barely noticeable way. Light linen is prone to shifting and puckering, and lined pants are hemmed a little differently.
Before you cut out the material, put on the pants with the shoes that you will most likely wear. Measure both legs, make sure that the length is right while standing normally, and allow room for the hem. In case of any doubt, you can pin or tack the pants temporarily and try them on.
What Does It Mean to Hem Pants?
To hem your pants is to sew together the lower edges of the legs so that they do not unravel or come loose to affect the desired height of your pants. There is some additional material that is turned inside and stitched to give the pants their proper shape and size.
Hemming your pants is not similar to cuffing the pants, where you just roll the bottom up, because in cuffing the pants, you create a visible edge on the pants.
The hem is normally inside the leg in the case of conventional hems, whereas most of the jeans are already factory-hemmed with the help of fading, stitching, and a thick edge.
A proper hem must be balanced at the two legs, conforming to the design of the leg of the pants, and should not add any extra volume. There are different hem lengths depending on the style of pants; for dress trousers, there can either be a break or no break at all.
What You Need to Hem Pants
Collect your sewing materials before you start. Proper sewing equipment will help you measure correctly, keep the crease straight, and ensure your fabric does not get damaged.
These sewing materials should include a flexible measuring tool or tape measure, a piece of chalk, sewing clips or straight pins, an iron and ironing board, sharp scissors, matching thread, and a hand sewing needle or sewing machine.
If you want to sew without a sewing machine, use iron-on hemming tape or temporary fabric tape that is compatible with the material.
Make sure you use thread that matches the color of the pants. Jeans require heavy duty thread and a needle designed for sewing denim. Lighter weight materials usually call for a smaller needle and thread.
You will need a seam ripper in case you have to remove the previous hem. You can use a hump jumper when sewing thick denim seams.
Make sure to read the care label carefully and test any heat-sensitive items in a discreet spot first. Certain artificial fibers will melt and shine if exposed to too much heat from an iron. Iron at the proper temperature setting and use a pressing cloth if necessary.
How to Measure and Mark Pants for Hemming
Measuring accurately is the first step to getting a proper hemming job done. Wear the pants along with your preferred footwear and ask somebody for help in measuring, if necessary.
Do the measurements standing upright wearing the pants in the usual way. Otherwise, there is a chance that the result will not be satisfactory.
First of all, determine the place where the lower hem of the pants is supposed to end. Usually, the lower part of pants ends just above the upper part of the foot.
This, of course, is conditional and depends on the style of the pants and the style of your footwear. Pin the spot you want to have as the lower point of the pants.
Now put off your pants and place them on a flat surface, without stretching the fabric. Align the side and inseam seams. Either measure the distance from the lower edge of the pants to the fold you have pinned, or measure the distance that needs to be cut off. Take measurements of each leg separately: even readymade pants do not necessarily coincide exactly.
Use tailor’s chalk or an appropriate marker to mark the line at which the garment will be folded. Mark the hemming allowance underneath that line.
This allowance varies according to the type of fabric and the desired look, but in many cases of everyday pants, 1 to 2 inches of fabric are needed for hemming conventionally; however, other allowances could be necessary depending on the type of fabric used.
Fold the fabric at the marked line and iron it; pin the fabric in its new position. It would be best to try on the pants at this stage.
How to Hem Pants With a Sewing Machine
A sewing machine will work well for creating a durable and neat hem on your garments, especially if you’re dealing with regular pants, cotton pants, and most of the jeans out there.
Make sure to use the appropriate color of thread and suitable needle for your fabric. Try stitching on a sample piece of material beforehand if possible.
Prepare and Mark the Hem
Unsew the old hem if it is bulky or interferes with making the new hem smooth. Cut away any stray threads and press the old hem as much as possible. Mark the final measurement for both legs as well as the measurement for the hem itself.
In case the pants narrow considerably at the bottom, make sure that the folded portion lies down smoothly; an extremely narrow leg may require careful measurements of the hem allowance.
Do not cut the extra cloth until you are sure of the length. If the pants just need minor alteration, you may be able to tuck away the excess fabric without cutting it, but an abundance of excess fabric results in a bulky hem.
Fold and Press the Fabric
Fold the bottom edge toward the wrong side on the marked line for the hem. To ensure a tidy look, you can turn the raw edge under by 1/4″ and then fold up the complete allowance for the hem. The actual fold will depend on the material and the amount of allowance.
Secure the fold using pins or clips, but keep the pins away from the machine’s needle. If the fabric is sensitive to heat, choose the correct temperature on your iron and use a pressing cloth. Do not stretch the pants while pressing because it may cause the hem to flare or ripple.
Pin and Sew a Straight Stitch
Select straight-stitch on the sewing machine and determine the appropriate stitch length based on the type of material used. Begin near an inseam, where both starting and ending stitches will be concealed.
Ensure the folded edge is always at the same distance from the needle and sew slowly along the leg. Remove the pins before they enter the presser foot.
Overlap the initial and final stitches slightly and reinforce the seam with some backstitches if possible. Avoid pulling the material while sewing as it can ruin the hem and create puckers.
When working with thick denim, use a denim needle and don’t force the sewing machine over bulky seams. Turn the handwheel manually when necessary.
Finish the Raw Edge and Press
As long as the rough edge is wrapped in two folds, it is safe from most fraying. In the event that the edge is left open within the leg area, use an appropriate finishing technique such as a zigzag stitch or an overlock stitch.
Once the hemming process is done, trim excess thread and press the hem on both sides as required. Use pressing cloth where applicable to prevent the fabric from becoming shiny. Allow the pants to cool before putting them on.
Common Sewing-Machine Mistakes
Issues include stitching too near the edge, using unsuitable needles and threads for the material, stretching the material while sewing, and forgetting to measure the length before cutting. Pinning unevenly may result in the hem rising or sagging around the legs.
In case the sewing machine skips stitches, ensure that you have not used a bent or dull needle. Should the fabric pucker, try a different stitch length and make sure you do not pull the fabric. Practice on a test piece of material before undoing the hem.
How to Hem Pants Without Sewing
This type of hemming works very well for quick alterations, for traveling, for temporary purposes, or when you do not have access to your sewing tools. It does not work well with all types of garments.
Tape may not adhere to heavy denims, rough fabrics, stretchable fabrics, or pants that require regular washing at a high temperature.
How to Use Iron-On Hemming Tape
The iron on hemming tape contains heat-sensitive glue which holds together the folded material. The material is first measured and marked for the needed length.
Then fold the material inward and press it down. The tape is then placed inside the fold as per the instruction of the manufacturer.
Iron using the settings recommended by the manufacturer. Some require the use of a pressing cloth, while others require the iron to be used directly. In case of such instructions, do not slide the iron, but lift and press it. Wait until the material cools down completely to test the result.
The hemming tape is suitable for light and medium weight materials, but it may stiffen the hem or remain as residues. Try it first, especially when working with fragile, elastic, coated, or heat sensitive materials.
If the hem becomes loose after washing, repeat the procedure according to the instructions or sew it.
How to Use Temporary Fabric Tape
Fabric tape is helpful in case you need to make an immediate change for a temporary basis like for an occasion or for just a day wear. You should first fold your fabric according to the required length and then press the folded area properly. Place the fabric tape between the folded parts as mentioned in the instructions.
Temporary tape cannot be used in place of sewing a permanent hem. The adhesion of the tape could get weak due to any kind of body movement or sweat. It should be made sure that the tape which you use is meant for clothes and can be removed easily.
How to Make a Temporary Fold or Cuff
In case of a no product alternative, simply fold the excess material inwards and make a nice temporary fold, or roll the material outwards to make an observable cuff. Even out the fold along the leg, and examine it in a mirror by putting on the intended footwear.
Loose folds will sag when one walks about, therefore it is suitable for temporary use and not a permanent change. The thickness of materials will determine whether bulky cuffs or light cuffs will result from folding.
In case safety pins are utilized, they should be done invisibly from the inside and only if they are secure enough not to pierce through.
When No-Sew Hemming Is Not Suitable
It is advisable to avoid the use of sticky tape when dealing with expensive pants, structured pants, lined pants, thick pants, stretchy pants, and those pants which are made using fabrics that will not withstand the necessary temperature.
It could also not be advisable to use sticky tape if the garment requires lots of laundering or dry cleaning. In case the fabric is fragile or the hemming process is affecting the drape of tailor-made trousers, then it would be wise to go for sewing.
If in doubt, one could try the material on an invisible seam allowance or seek help from a tailor.
How to Hem Dress Pants
It is important to make dress pants have a nice hem that will go well with their break and drape. This is necessary not only for shortening of the pant legs, but for maintaining the shape of the pants as well. A hand-made blind hem is most commonly used for such purpose, although other options can also be considered.
How to Choose the Right Trouser Break
Trouser break refers to the way in which the front part of the leg touches the shoe. Full breaks create a prominent crease or fold on the front of the trousers, slight breaks involve minimal contact, while no breaks or crops have minimal fabric touching the shoe. There is no correct trouser length for all suits or styles.
Try out the trousers with the actual shoes that you will wear and see what works best for the trouser fit. Slightly tight or tapered trousers tend to look good with a small break, while conventional suit trousers can be worn with a slight or full break. The back of the trousers mustn’t touch the floor.
How to Make an Invisible Hem
To create an invisible hem, fold and press the fabric, then use a blind stitch that only takes a little bit of the outer fabric. Using the right thread color and using a smaller needle will ensure the stitches remain inconspicuous. Do it slowly and check on the exterior to make sure that the stitches are not appearing as large dots.
Most sewing machines come with the blind hem setting and a blind hem foot. Refer to the machine manual to know how to set the fold. For expensive suit pants or wool fabrics, hand blind hemming can be the preferred option.
How to Hem Lined Dress Pants
The lining in pants has an additional layer that makes it difficult to sew the hem. The lining must be smooth and must not raise the external layer upwards. Most of the time, the lining in clothing is put on separately and therefore requires adjustment too.
You should never cut any layer in the pants until you understand how it was joined together. If there is any special way of joining the lining to the outer layer of pants or if the pants are expensive, then a tailor should do the job.
When to Visit a Tailor
Tailors make sense when considering pants that are expensive, lined, wide-legged with the drape well thought out, complex cuffs, or jeans where maintaining the original hemming is vital.
It may also be advisable when the pants require substantial alteration in terms of length, have an unusual construction, or are made from delicate material.
If the pants in question are part of a suit, you might want to inquire about whether the hemming ought to be formal in line with the formalities of the jacket and the type of shoes worn.
How to Hem Different Types of Pants
Each cloth or silhouette demands a particular approach. Prior to selecting a hem technique, you should think about the weight, elasticity, type of weave, size of the legs, lining, and whether the existing hem is a part of the design.
How to Hem Jeans
When repairing regular jeans, a folded seam made by a sewing machine will be a strong solution. You should use denim needles and strong thread, and be careful when stitching at places where the inseam and side-seam seams intersect, since there is a lot of thickness. In case keeping the original hem of the jeans is necessary, you should apply a technique that keeps the hem or consult a tailor.
How to Hem Wide-Leg Pants
With wide-legged pants, any irregularities in the hemline will be more visible because of the wide opening and because the fabric can shift around your shoes.
Measure by wearing the shoes you will be wearing with the pants, aligning the side seams, and making sure the length is right all the way around.
In case of flowy fabrics, do not stretch the fabric while measuring or stitching. A hand-basting guideline may help to keep the hem straight.
How to Hem Linen and Lightweight Pants
Both linen and light weight cotton have the potential to wrinkle and shift while hemming. Use an iron at an appropriate temperature for the material, pin or clip the material appropriately, and choose the right needle for lightweight woven fabric. Double fold narrow hem works great since it does not add any bulk to the material.
Lightweight materials tend to pucker and the needle marks tend to show up. Therefore, it is best to test the tension and length of stitches on a sample first.
How to Hem Kids’ Pants
Length adjustments may be required often as the child grows. If one intends to lengthen the pants further in future, extra material should be left inside where it is possible without compromising the pattern and fit of the pants.
Temporary cuffs or removable stitches work for a short time while permanent hemming is more reliable for the activities involved and frequent washing.
The pins should not be left in the pants once completed and any hanging threads or sharp fastening points should be avoided inside the pants. The pants should be checked after washing due to shrinking of certain materials.
How Long Should Pants Be?
Ideal length of a pair of pants depends on the type of pants, heel height, material, and personal preference. A good start would be to select the length with the shoes that will be worn with the pants, then look at the front, side, and back lengths.
How Long Should Jeans Be?
Straight-leg and bootcut jeans often reach the top of the shoe or create a small break, depending on the style. Slim jeans may sit closer to the ankle, while cropped jeans are intentionally shorter. Avoid a length that causes the back hem to scrape the ground or the front to bunch excessively.
How Long Should Dress Pants Be?
Dress pant length depends on the desired trouser break. Traditional suit trousers may have a slight break, while modern slim-fit styles often use a smaller break or no break.
The hem should work with the shoe and the overall silhouette. When in doubt, pin the length and view it from the front and side before sewing.
How Long Should Wide-Leg Trousers Be?
Wide-leg trousers are often worn long enough to skim the top of the shoe, but the correct length varies with the cut and heel height. The hem should hang evenly without sweeping the floor.
Since the fabric may cover much of the shoe, try the pants on while standing and walking to make sure the length is practical.
How to Hem Cropped Pants
Cropped pants are designed to end above the ankle or at another intentional point on the lower leg. Decide where the crop should sit and compare both legs in a mirror.
A narrow hem can preserve a clean silhouette, while a visible cuff may suit casual styles. Check the finished length with the footwear you plan to wear.
How to Account for Shoes and Heels
Shoes can change the way pants fall, especially when switching between flats, sneakers, boots, and high heels. If you wear several shoe heights, choose the length based on the footwear you use most often or have separate pants hemmed for different shoes. Bring your usual shoes to a tailor appointment and wear them during home measurements.
How Much Fabric Should You Leave When Hemming Pants?
The amount of fabric to leave depends on the pant style, fabric thickness, and hem method. A conventional hem on everyday pants often needs around 1 to 2 inches of allowance, but this is only a starting point.
Some tailored trousers use a different allowance, and a narrow hem on lightweight fabric may need less. Follow a pattern or garment-specific instructions when available.
Remember that the hem allowance is the fabric folded inside the pant leg, not the amount you plan to shorten. If you need to remove 2 inches from the finished length, you must still leave enough extra fabric below the new fold to create the hem. Mark the finished line and the cutting line separately so they are not confused.
For jeans with a preserved original hem, the calculation is different because you must account for the width of the original hem and the position where it will be reattached. Measure twice, pin the planned alteration, and try the pants on again before cutting.
Common Hemming Mistakes to Avoid
The most common mistake is cutting fabric before confirming the finished length. Always pin or baste the hem first, try the pants on with the intended shoes, and check both legs. It is much easier to remove a temporary stitch than to restore fabric that has been cut too short.
Another frequent problem is measuring on a wrinkled surface or stretching the pant leg while marking. Smooth the fabric without pulling it, align the seams, and measure both legs independently. Use chalk or a removable marker that is safe for the fabric.
Avoid using the wrong needle, thread, stitch length, or iron temperature. A heavy needle can leave visible holes in delicate fabric, while a weak needle can struggle with denim. Excessive heat can damage synthetics, and too much tension can cause puckering. Test the setup on a scrap whenever possible.
Do not sew over pins or force a sewing machine through thick seams. Remove pins as you approach them and use an appropriate needle and careful speed for bulky areas.
Finally, do not assume adhesive tape is permanent: check the product instructions and consider how often the pants will be washed or dry-cleaned.
How to Fix Common Hemming Problems
How to Fix Uneven Pant Legs
Put the pants on with the intended shoes and identify which side is too long or too short. Mark the desired length again while standing naturally, then lay the pants flat and compare the marks.
If the hem has already been sewn, unpick the affected section carefully, remeasure, and press the fold before stitching again.
Check whether the uneven appearance comes from the hem itself or from the way the pants sit on the body. If one leg consistently hangs differently because of posture or garment construction, a tailor may be able to make a more precise adjustment.
How to Fix Visible Stitching
If stitches show on the outside of dress pants, they may be catching too much of the outer fabric. Carefully remove the visible section with a seam ripper, taking care not to cut the garment, and restitch with smaller blind-hem catches. Matching thread can reduce visibility, but stitch placement matters most.
For machine-sewn hems where visible stitching is intended, use a consistent distance from the edge and matching thread for a clean finish. If the fabric has needle holes that remain after unpicking, press gently according to the care label; some marks may not disappear completely.
How to Prevent Fraying
Fraying occurs when the raw fabric edge unravels. Enclose the edge in a double fold when there is enough allowance, or finish it with a zigzag, overlock, or another suitable seam finish.
Lightweight fabric may need a narrow, carefully pressed fold, while heavy denim needs a finish that does not create excessive bulk.
If the pants have already frayed, trim only loose threads and avoid cutting away more fabric than necessary. Finish the edge before securing the hem.
How to Reduce a Bulky Denim Hem
Bulky hems often form where the side or inseam overlaps with several folded layers. Reduce unnecessary layers only if doing so will not weaken the garment, and use a needle made for denim. A hump jumper or scrap of fabric can help the presser foot remain level as it crosses a thick seam.
Pressing the seam allowances in opposite directions may reduce the thickness at intersections. If the machine cannot safely handle the layers, do not force it; a tailor with industrial equipment may achieve a cleaner finish.
How to Fix Hem Tape That Comes Loose
First check the tape packaging to confirm whether it is designed for the fabric and washing method. If the bond has loosened, let the garment cool and dry, then follow the manufacturer’s reapplication instructions. Do not apply extra heat automatically, because the fabric or adhesive may be damaged.
If the tape continues to release, remove it if the instructions allow and use a sewn hem instead. Residue can be difficult to remove from some fabrics, so test any cleaning method in a hidden area or seek professional advice.
How to Prevent Puckered Fabric
Puckering can happen when thread tension is too tight, the stitch length is unsuitable, the fabric is stretched while sewing, or the needle is not appropriate for the material. Test the settings on a scrap, support the fabric without pulling it, and sew at a steady pace.
For lightweight or stretchy fabric, use a suitable needle and stitch type. Pressing may relax minor ripples, but persistent puckering usually needs the affected stitching removed and sewn again with corrected settings.
What to Do if Pants Become Too Short
If the pants are only slightly too short, check whether the original hem can be let down to release extra fabric. Remove the stitching carefully, press out the old crease, and see how much usable allowance remains. The old fold line may still be visible, especially on faded or frequently washed fabric.
If there is not enough fabric to create a proper hem, options may include adding a coordinating cuff or contrast facing, using a decorative band, or asking a tailor about a discreet extension.
The best solution depends on the fabric, style, and how much length is missing. Avoid attaching an improvised extension that makes the pants uncomfortable or changes the drape unexpectedly.
Should You Hem Pants Yourself or Visit a Tailor?
Hemming pants at home can save money and is a practical skill for simple alterations. A straight machine-sewn hem is often manageable for beginners, and hand stitching can create a discreet finish with patience. No-sew products may help with temporary adjustments, but they are not ideal for every fabric or garment.
A professional tailor may be the better option for expensive dress pants, lined trousers, unusual fabrics, significant length changes, complicated cuffs, or jeans where preserving the original hem matters.
Tailors can also assess how the pants hang with your posture and footwear, which can be difficult to judge from a flat measurement alone.
Choose based on the garment’s value, the complexity of the alteration, and how durable the finish needs to be. If you are learning, start with an inexpensive pair and practise measuring, pressing, and stitching before altering a favourite garment.
Hemming Pants FAQs
How much fabric should I leave for a pants hem?
Leave about 1½″ below the finished length: ½″ for the first fold and 1″ for the hem itself. Dress pants often use a deeper 2″ hem.
What stitch is best for hemming pants?
A straight stitch is easiest and works well for jeans and casual pants. For dress pants, a blind hem stitch (by machine or by hand) is almost invisible from the outside.
Can I hem pants without a sewing machine?
Yes. You can hand sew a blind stitch, or use iron-on hem tape for a quick no-sew hem.
How do I make sure both legs are the same length?
Measure the inseam from the crotch seam to your marked line on the first leg, then mark the second leg at the same measurement. Cut one leg first and use it as a guide for the other.
Where should pants hit on the shoe?
It depends on the style, but for most trousers the back hem should just touch the top of the shoe heel, with a slight break at the front.
How long does it take to hem pants?
About 30–45 minutes on a sewing machine for a beginner, and longer by hand.
Note: the HowTo schema (JSON-LD) and styling stay in the WordPress Custom HTML version of this guide.
Related
